Do you have a single piece of vinyl siding that has been damaged and needs replaced? This job may seem daunting at first, but you really need only a single tool in addition to a hammer, a pair of pliers, and some tin snips.
This siding tool is called a siding removal tool, and costs under ten dollars. It's basically a curved metal hook with a plastic handle. The hook is made to fit under the siding to pull the siding above the piece being replaced. The job, described in a general way, goes like this: go all the way down the piece of siding in this manner, to expose the nails which need to be removed to take down the damaged piece.
Pull the nails, push down on the damaged siding to remove it from the "starter strip" it is connected to, then replace with a new piece that is as close to the original as you can find. You'll need to cut it to match, hence the tin snips. Once the new piece is cut, slide it into place, and use the siding removal tool to hoist the new piece into place on the "starter strip". You then nail it into place, but leave the nails sticking up a bit for easy removal (remember what the old nails looked like before you pulled them? Hammer to about the same depth.) Then push the upper panel into position. The last thing to do is do what you did with the siding removal tool, but in reverse. This is a general description, be sure to try a replacement job on a single piece to fully understand the procedure before undertaking a large replacement job.
Which air compressor is right for me?
Can I plug my air compressor into any socket?
What should I look for in air tool accessories?
Are there replacement parts for my air tools?
Should I get a big or small air compressor?
Should I rent or buy my first air compressor
What is the compressor duty cycle?
How heavy is too heavy for a tool belt or tote?
Are there specialty tool belts for women?
How can I organize all these tools?
What can I do about the oily residue at the bottom of my tool box?
How can I secure my hand tools?
What should I do with my old hand tool storage solutions after I outgrow them?
When would I need a screwdriver magnetizer/demagnetizer?
What good is a magnetic sweeper?
Why do I need a rechargeable flashlight?
What's in a drywal repair kit?
How do I fix cracks in my drywall?
What accessories are available for my rechargeable flashlight?
Do I need a vacuum pick up tool?
What options do I have with cordless tool kits?
Where do I start with cordless tools?
What does my cell phone have to do with cordless power tools?
How does cold weather affect cordless battery life?
What can I do about my bottom heavy cordless drill in the tool belt?
What are my cordless tool battery choices?
What should I do with these old tools?
Should I buy discount power tools?
What should I look for in used power tools?
What safety issues are connected with circular saws
When would I need a heavy-duty vise?
What is a variable angle strap clamp?
What is the difference between a permanent and temporary clamp?
What are my staple gun options?
What rivet tools should I buy?
How would I use blind rivet tools and blind rivets?
What kind of staple gun should I get for upholstery?
Is soldering material dangerous?
What good is a measuring wheel?
What are those extra markings on my tape measure?
How can I get better results from my tape measure?
Can I get a combination stud finder and laser level?
Why does my stud finder keep "finding" nails?
My bandsaw has an auto cut-off. Is it safe to run unattended?
How do I choose the right blade for my circular saw?
What is the difference between contractor table saws and cabinet saws?
What should I look for in table saw blades?
What should I know about an electric drill bit sharpener?
What are my choices in router bits?
What should I know about bit selection and cutting time?
What safety issues are connected to routers?
Can I build an inexpensive table for my router?
What kinds of bolt cutters are there to choose from?
What should I include in my first set of pliers?
Where can I find left-handed tools?
What kinds of files should I add to a woodworking kit?
What should go into my first automotive tool set?
I've got all my tools. Anything else I should know?
Will I need additional tools for car stereos, alarm systems, and other add-ons?
Should I buy metric or standard wrenches?
What is a crowfoot socket wrench?
My socket set is so large I can't find any of them quickly. Help!
What safety issues are raised by dull tools?
What are my rights and responsiblities on the job with power tools?
What's the difference between safety glasses and safety goggles?
What can I do to increase safety on the job with newcomers?
What can I do to increase my personal safety margin around power tools?
Where can I find the federal guidelines for power tool and hand tool safety in the workplace?
Can I texture a drywall project?
How do I fix a "doorknob hole" in my drywall?
Can I install bathroom or decorative tile directly onto drywall?
What should I know to safely install my new gutters
What do I need to replace vinyl siding?
Should I add primer to my drywall before painting?
What can I do about all this chalky drywall residue?